THE DEXTER CORP -- EPK 0151, EPOXY PATCH KIT PART B, AB0151  -- 8040-00-059-5477
<pre>=====================  Product Identification  =====================

Product ID:EPK 0151, EPOXY PATCH KIT PART B, AB0151
MSDS Date:12/19/1988
FSC:8040
NIIN:00-059-5477
Kit Part:Y
MSDS Number: BCWPJ
=== Responsible Party ===
Company Name:THE DEXTER CORP
Address:ONE DEXTER DRIVE
City:SEABROOK
State:NH
ZIP:03874
Country:US
Info Phone Num:603-474-5541
Emergency Phone Num:603-926-0910
Preparer's Name:DR. SHELDON CLARK
CAGE:HO354
=== Contractor Identification ===
Company Name:DEXTER CORP DEXTER ELECTRONIC MATERIALS DIV
Address:15051 E DON JULIAN RD
Box:City:LA PUENTE
State:CA
ZIP:91746
Country:US
Phone:818-968-6511
CAGE:12405
Company Name:THE DEXTER CORP
Address:ONE E WATER ST
Box:1282
City:WAUKEGAN
State:IL
ZIP:60085
Country:US
Phone:708-623-4200
CAGE:HO354

=============  Composition/Information on Ingredients  =============

Ingred Name:NO INGREDIENT FOR THIS FORMULATION_INGREDIENT

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:MATERIAL IS CORROSIVE TO SKIN. MAY
    CAUSE CHEMICAL BURNS TO SKIN AND EYES. REPEAT CONTACT MAY CAUSE
    SENSITIZATION. SIGNS & SYMPTOMS OF EXPOSURE:SKIN RASH, IRRITATION;
    POSSIBLE BURNS.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.

=======================  First Aid Measures  =======================

First Aid:INGEST:CALL MD IMMEDIATELY . INHAL:REMOVE TO FRESH AIR.
    SUPPORT BREATHING (GIVE O*2/ARTF RESP) . EYES:IMMEDIATELY FLUSH
    W/POTABLE WATER FOR MINIMUM OF 15 MINUTES, SEEK ASSISTANCE FROM MD
    ( ). SKIN:FLUSH W/COPIOUS AMOUNTS OF WATER. CALL MD .

=====================  Fire Fighting Measures  =====================

Flash Point Method:COC
Flash Point:265F,129C
Extinguishing Media:DRY CHEMICAL OR HALON FIRE EXTINGUISHER, OR WATER
    SPRAY, FOAM OR FOG.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA & FULL PROTECTIVE
    EQUIPMENT .
Unusual Fire/Explosion Hazard:DENSE SMOKE AND TOXIC GASSES MAY BE
    LIBERATED.

==================  Accidental Release Measures  ==================

Spill Release Procedures:SCRAPE UP EXCESS & TRANSFER TO METAL
    CONTAINERS. WIPE UP REMAINING RESIDUE WITH SOLVENTS, OBSERVING
    SOLVENT FLAMMABILITY CAUTIONS, OR USE DETERGENT.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:KEEP COOL IN ACCORDANCE WITH LABEL
    INSTRUCTIONS. FOLLOW RECOMMENDED CURING SCHEDULE.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NOT REQUIRED WITH GOOD INDUSTRIAL VENTILATION;
    NIOSH/MSHA APPRVD ORGANIC RESPIRATOR.
Ventilation:LOCAL EXHST: PREFERABLE. MECH: ACCEPTABLE
Protective Gloves:RUBBER/PLASTIC
Eye Protection:ANSI APPROVED CHEM SAFETY GOGGLES 
Other Protective Equipment:AS NEEDED TO PROTECT SKIN AND CLOTHING.
    EMERGENCY EYE BATH AND DELUGE SHOWER .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
FILLER PARTICLES ARE THOROUGHLY WETTED BY VEHICLE SO AIRBORNE EXPOSURE
    DOES NOT OCCUR UNLESS CURED MATERIAL IS SUBSEQUENTLY GROUND,
    MACHINED OR SANDED. CNDTNS TO AVOID (POLYM):TO BE BONDED. FAILURE
    TO	OBSERVE CAUTIONS MAY RESULT IN EXCESSIVE HEAT BUILD-UP WITH THE
    RELEASE OF TOXIC GASSES.

==================  Physical/Chemical Properties  ==================

HCC:N1
Boiling Pt:B.P. Text:531F,277C
Vapor Pres:<.01
Vapor Density:>1
Spec Gravity:0.98
Evaporation Rate &amp; Reference:<0.01
Solubility in Water:20%
Appearance and Odor:AMBER COLORED LIQUID WITH SLIGHT AMMONIACAL ODOR

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:NITROGEN OXIDES, CO*2, CO, NO*X,
    ALDEHYDES, ACIDS AND UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:AVOID MIXING RESIN & CURING AGENT IN
    BATCHES GREATER THAN 1 POUND TOTAL. DO NOT HEAT MATL UNLESS CURING
    SURFS (SUPDAT)

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE OF AS HAZARDOUS WASTE ACCORDING TO DOT
    HAZARD CLASS. IF NOT REGULATED BY DOT DISPOSE OF AS ORM-E. DISPOSAL
    METHOD CAN BE LAND BURIAL OR CHEMICAL INCINERATION.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.