ITW DEVCON CORPORATION -- 5 MINUTE EPOXY RESIN  -- 8040-01-034-0401
<pre>=====================  Product Identification  =====================

Product ID:5 MINUTE EPOXY RESIN
MSDS Date:12/14/1989
FSC:8040
NIIN:01-034-0401
Kit Part:Y
MSDS Number: BLJLZ
=== Responsible Party ===
Company Name:ITW DEVCON CORPORATION
Address:30 ENDICOTT ST
City:DANVERS
State:MA
ZIP:01923
Country:US
Info Phone Num:508-777-1100
Emergency Phone Num:508-777-1100
CAGE:16509
=== Contractor Identification ===
Company Name:DEVCON CORP
Address:30 ENDICOTT ST
Box:City:DANVERS
State:MA
ZIP:01923-3753
Country:US
Phone:1-508-777-1100
CAGE:16059
Company Name:ITW DEVCON CORPORATIO
Address:30 ENDICOTT ST
City:DANVERS
State:MA
ZIP:01923
Country:US
Phone:508-777-1100
CAGE:16509

=============  Composition/Information on Ingredients  =============

Ingred Name:BISPHENOL A DIGLYCIDYL ETHER RESIN (POTENTIAL SKIN
    SENSITIZER)
CAS:25068-38-6
RTECS #:KD4380000
Fraction by Wt: > 60%
Other REC Limits:NONE SPECIFIED

Ingred Name:VOC:0 LBS/GAL (EPA REFERENCE METHOD 24)
RTECS #:9999999VO
Other REC Limits:NONE SPECIFIED

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:ORAL LD50 (RAT):11,400 MG/KG *
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:PROLONGED OR REPEATED SKIN CONTACT MAY
    CAUSE SENSITIZATION, WITH ITCHING, SWELLING, OR RASHES ON LATER
    EXPOSURE.	   *DERMAL LD50 (RABBIT): >20,000 MG/KG.  INHALATION
    LC50 (RAT): NO DEATHS IN SATURAT ED AIR; EXPOSURE TIME 8 HOURS.
Effects of Overexposure:EYES:MILD IRRITATION. SKIN:MILD IRRITATION.
    INHALATION:NO DATA. THE LOW VAPOR PRESSURE OF THE RESIN MAKES
    INHALATION UNLIKELY IN NORMAL USE. INGESTION:ACUTE ORAL TOXICITY IS
    LOW. MAY CAUSE GASTRIC DIS TRESS.
Medical Cond Aggravated by Exposure:ALLERGIES, ECZEMA, OR OTHER SKIN
    DISORDERS.

=======================  First Aid Measures  =======================

First Aid:EYES:FLUSH W/CLEAN WATER FOR 15 MIN WHILE GENTLY HOLDING
    EYELIDS OPEN.GET IMMED MED ATTN.SKIN:WASH THOROUGHLY W/SOAP & WARM
    WATER.CONSULT A PHYSICIAN IF IRRIT DEVELOPS.INHALATION:REMOVE
    PATIENT TO FRE SH AIR.GIVE OXYGEN IF BREATHING IS DIFFICULT.GET MED
    ATTN IF SYMPTOMS PERSIST.INGESTION:DO NOT INDUCE VOMITING.GIVE TWO
    GLASSES OF WATER TO DILUTE(UNLESS PATIENT IS UNCONSCIOUS).GET
    MEDICAL ATTN.

=====================  Fire Fighting Measures  =====================

Flash Point Method:PMCC
Flash Point:<400F,<204C
Extinguishing Media:CO2, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:FIREFIGHTERS SHOULD WEAR SELF-CONTAINED
    BREATHING APPARATUS AND PROTECTIVE CLOTHING.
Unusual Fire/Explosion Hazard:NONE

==================  Accidental Release Measures  ==================

Spill Release Procedures:PREVENT SKIN AND EYE CONTACT. LARGE SPILLS MAY
    BE ABSORBED ON INERT MATERIAL SUCH AS SAND OR VERMICULITE. SCRAPE
    SPILL UP INTO NONPOROUS CONTAINER. CLEAN SPILL AREA WITH STRONG
    DETERGENT AND WATER. US E SOLVENTS ONLY WITH APPROPRIATE CAUTION.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE IN A COOL,DRY PLACE.HANDLE MIXED
    RESIN & HARDENER IN ACCORDANCE WITH THE POTENTIAL HAZARD OF THE
    CURING AGENT USED.REMOVE CONTAMINATED CLOTHES**
Other Precautions:**AND PROTECTIVE GEAR. CLEAN THOROUGHLY BEFORE USING
    AGAIN. DISCARD CONTAMINATED LEATHER ARTICLES. WASH THOROUGHLY AFTER
    USING, PARTICULARLY BEFORE EATING OR SMOKING.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NONE REQUIRED AT NORMAL HANDLING TEMPERATURES.
Ventilation:LOCAL EXHAUST IS RECOMENDED FOR CONFINED AREAS. GENERAL
    MECHANICAL IS ADEQUATE FOR NORMAL USE.
Protective Gloves:IMPERVIOUS GLOVES
Eye Protection:SAFETY GLASSES WITH SIDE SHIELDS.
Other Protective Equipment:OTHER GEAR AS REQUIRED TO PREVENT SKIN
    CONTACT.
Work Hygienic Practices:WASH THOROUGHLY AFTER USING, PARTICULARLY
    BEFORE EATING OR SMOKING.
Supplemental Safety and Health
THIS INFO APPLIES TO RESIN PART OF KIT. AFTER CURING, THE PRODUCT IS
    NON-HAZARDOUS.

==================  Physical/Chemical Properties  ==================

Vapor Pres:NIL
Vapor Density:> 1
Spec Gravity:1.2
pH:7 (5%)
Evaporation Rate &amp; Reference:< 1 (BUAC=1)
Solubility in Water:NIL
Appearance and Odor:THICK, AMBER LIQUID WITH LITTLE ODOR.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS AND STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:OPEN FLAME AND EXTREME HEAT.
Hazardous Decomposition Products:OXIDES OF CARBON, ALDEHYDES AND ACIDS
    FROM INCOMPLETE COMBUSTION.
Conditions to Avoid Polymerization:HEAT IS GENERATED WHEN THIS RESIN IS
    MIXED WITH AMINES OR EPOXY HARDENERS. BE CAREFUL WHEN MIXING LARGE
    AMOUNTS.

====================  Disposal Considerations  ====================

Waste Disposal Methods:REMOVE TO A WASTE FACILITY OPERATING IN
    COMPLIANCE WITH STATE AND LOCAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.